Black multi-purpose adhesive tape

 

Advantages

  • All-round adhesive tape for internal and external use, 6 months of outdoor exposure
  • Easy to tear off by hand with a soft fleece backing
  • Suitable for sealing to penetrations
  • Can be plastered over
  • Also used for windtight adhesion of wall lining membranes behind suspended façades
  • Waterproof adhesive
 

Application

Exterior use: Creation of a windproof seal for wall lining membranes using pro clima SOLITEX FRONTA PENTA, -QUATTRO and -WA and for underlay and sarking membranes. Windproof bonding of wood-based panels for underlays. Airtight bonding of on-roof and refurbishment vapour retarders and airtight membranes.

Interior use: Airtight bonding of vapour retarders and airtight membranes and of airtight wood-based panels.

All bonding can be carried out between these products as well as to smooth adjacent non-mineral components (z. B. pipe feed-throughs, skylights) for both interior and exterior use.

Technical specs

  Material
Backing special PP fleece
Adhesive waterproof SOLID adhesive
Release film siliconized paper
Attribute Value Norm
Colour black
Exposure time 6 months
Bonding requirement, non-aged/aged passed DIN 4108-11
Can be plastered over yes
Application temperature above -10 °C ; 14 °F
Temperature resistance permanent -40 °C to 90 °C ; -40 °F to 194 °F
Storage cool and dry

Image gallery - Application guide

General conditions

The bonds should not be subjected to tensile strain.
Once membranes have been stuck, the weight of the insulation material must be supported by laths. Adhesion should be supported by additional laths, if necessary.
Press firmly to secure the adhesive tapes in place. Ensure that there is sufficient resistance pressure.
Windproof, airtight or rainproof bonding can only be achieved on vapour retarders or underlay/sarking/facade membranes that have been laid without folds or creases.
Ventilate continuously and systematically to prevent build-up of excessive humidity; use a dryer if necessary.
When plastering, please observe the recommendations of the plaster manufacturer for non-absorbent subsurfaces. A bonding course may be necessary.

Substrate

Before adhesion is carried out, subsurfaces should be brushed off, wiped clean with a cloth or cleaned using compressed air.
Adhesion to frozen surfaces is not possible. There must be no water-repellent substances (e.g. grease or silicone) on materials to be bonded. Subsurfaces must be sufficiently dry and stable.

Permanent adhesion is achieved on all pro clima interior and exterior membranes, other vapour retarder and airtight membranes (e.g. those made of PE, PA, PP and aluminium) as well as other underlay/sarking and wall lining membranes (e.g. those made of PP and PET).
Bonding and joints are possible on planed and painted wood, hard plastics and metal (e.g. pipes, windows etc.), hard wood-based panels (chipboard, OSB, plywood, MDF and wood fibre underlay panels).
Wood fibre sub-roof panels and smooth mineral subsurfaces require pre-treatment with TESCON PRIMER before bonding. Concrete or plaster subsurfaces must not be sandy or crumbling.

The best results in terms of structural stability are achieved on high-quality subsurfaces.
It is your responsibility to check the suitability of the subsurface; adhesion tests are recommended in certain cases.
Pretreatment with TESCON PRIMER is recommended in the case of subsurfaces with insufficient stability.

Empfohlenes Produkt

SOLITEX FRONTA PENTA

SOLITEX FRONTA PENTA

5-ply wall lining membrane with double-layer, monotithic TEEE membrane, suitable for wall decking with gap widths of up to 50 mm

SOLITEX FRONTA QUATTRO

SOLITEX FRONTA QUATTRO

3-ply wall lining membrane with monolithic TEEE functional membrane, suitable for open jointed and closed façades

Zubehör

PRESSFIX

PRESSFIX

Pressing aid for pro clima adhesive tapes